Unless indicated otherwise, these features are available only at time
of manufacture.
Power Cords
The appropriate power cord is attached at the factory based on the
order designation country code except for the following:
- 6 ft Chicago (#9986) Factory or Field installable
Machine Nomenclature
- English (#2924)
- French (#2928)
- Japan (#2930) (Operator Panel Only)
- Spanish (#2931)
- Italian (#2932)
- French Canadian (#2935) (Keyboard Only)
If no language is specified, English (#2924) is supplied.
Attached System Types
The following codes indicate the attached system types:
- #9104 Attached to AS/400 or iSeries system
- #9106 Attached to RS/6000 or pSeries system
- #9109 Attached to ES/3090, ES/9000, S/390, or zSeries system
Other Specify Codes
(#9021) Virtual Drives Enhancement
This feature notifies the plant that a 3494 Model B10 or B20 VTS, or a
Model B18 VTS with feature #5264 (64 Additional Virtual Drives), is
attached to the Model L1x Tape Library Base Frame (and Model HA1 if
present). One feature is required on each 3494 Model HA1, L10, L12, and
L14 for each Model B18 VTS with feature #5264, or Model B10 or B20 VTS,
that is attached to the Model L10, L12, or L14 Tape Library Base Frame.
Maximum: Two.
Minimum: None.
Plant or Field Installable.
(#9041) High Availability Direct Attachment
(No Longer Available as of December 31, 1998)
If any device in the 3494 that contains Model HA1 Frames attaches to a
host system that uses direct attachment for library control (AS/400,
RS/6000, Sun, HP, and native VSE/ESA), then this feature must be
specified on all models of the 3494 shipping from the plant with the
Model HA1 Frames.
Maximum: One.
Field Installation: No.
Corequisite: Must be on all other models of the 3494 that are
shipping new with the Model HA1 Frames.
(#9046) PCI Library Manager - Plant
(No Longer Available as of October 29, 2004)
This feature indicates that this machine was shipped from the plant
with a library manager with PCI architecture including a faster 1.2 Ghz
processor and a mirrored dual disk drive, for performance and
availability improvements in the 3494. This feature code is for new
machine orders only, and should be on every machine shipped after
February 28, 2003. For currently-installed machines, refer to feature
#5046.
- Maximum: One.
- Field Installation: No.
(#9047) LAN PCI Library Manager - Plant Install
This feature provides the plant installation of a library manager (LM)
that supports EASH attachment of tape drives attached to open systems and
up to 64 LAN attached open system TCP/IP hosts. The LM has a PCI
architecture and includes a 1.2 Ghz processor and a mirrored dual disk
drive, to help improve performance and availability in the 3494. If this
feature is added to a 3494 that includes Model HA1 Frames, the other LM
must be feature #5046, #9046, or #9047.
Note: This LM does not come with four RS232 host connections and four
tape control unit serial connections. If that capability is required,
the Base Tape Control Unit Attachment feature (#5225) must be ordered
with this feature. Feature #5225 is also required if the other LM in the
3494 Tape Library that includes Model HA1 Frames has feature #5046 or
#9046.
- Maximum: One.
- Required: Feature #9047 (or #5047) is required when adding feature
#9040 (High Availability Attachment) to any installed Model Lxx that does
not contain feature #5046 or #9046 (PCI Library Manager) or feature #9020
(Model B20, B18, or B10 VTS Attachment).
- Plant Installation Only.
(#9184) EASH Enablement
This feature must be installed to enable a tape drive in the 3494 Tape
Library to connect to the library manager (LM) with an Ethernet Attached
Serial Hub (EASH) attachment. Up to 96 open system tape drives can be
connected to the LM through an EASH attachment.
- Maximum: One.
- Required feature: No. However, if open system attached tape drives
are in a 3494 Tape Library with the LAN PCI Library Manager feature
(#5047 or #9047), either this feature #5184 or the Base Tape Control Unit
Attachment feature (#5225) must be installed. Feature #9184 is required
if any frame in the 3494 Tape Library has feature #5184 (Ethernet
Attached Serial Hub) installed.
- Corequisites:
- Feature #5232 (Attachment Concentrator).
- Feature #5246 (Dual Path Concentrator).
- Feature #9184 must be on both the Model HA1 and the Model Lxx Frames
if the Model HA1 Frames are installed in the 3494 Tape Library.
- The 3494 Model Lxx must have an LM shipped after May 15, 2000, or one
of the following features:
- Feature #5047 or #9047 (LAN PCI Library Manager).
- Feature #5046 or #9046 (PCI Library Manager).
- Feature #9020 (Model B20, B10, or B18 VTS Attachment).
- Plant or Field Installation.
Remote Support Features
The following features are to provide rapid diagnostic and remote
support capability. The same modem and switch may be shared between the
following units:
- 3494 Model AX0, B10, B16, B18, B20, CX1, L10, L12, L14, L22, and HA1
- 3590 Model A60, A50, or A00
- 3490 Model F1A (or FC0) Control Unit (FC 3000 or 3500)
- 3592 Model J70
One of the following three features were used to provide remote
support on previous installations of the 3494 Models L12 and L22. New
shipments of a 3494 Model L12 or L22 should specify one of the IBM
TotalStorage Master Console features (#2713, #2714, or #2715).
(#2710) Remote Support Facility
This feature supplies a cable and connectors for connection to an IBM
supplied modem to enable remote diagnostic support. This feature should
only be specified on the first unit of each set of fourteen units in an
installation site.
- Maximum: One of FC 2710, 2711, or 2712.
- Field Installation: Yes.
(#2711) Remote Support Switch
(No Longer Available as of December 31, 2004)
This feature provides a switch, cables, and connectors for the
attachment of multiple units through the switch to a modem. It should be
ordered on the second unit attached to the modem in an installation. One
switch should be specified for every set of fourteen units in an
installation site.
- Maximum: One of FC 2710, 2711, or 2712.
- Field Installation: Yes.
(#2712) Remote Support Attachment
(No Longer Available as of December 31, 2004)
This feature provides an additional cable and connector to attach to
the Remote Support Switch (FC 2711). It should be ordered on the third
through the fourteenth unit attached to the Remote Support Switch in an
installation site.
- Maximum: One of FC 2710, 2711, or 2712.
- Field Installation: Yes.
IBM TotalStorage Master Console Features
The following features #2713, #2714, and #2715 provide connection to
an IBM TotalStorage Master Console (TSMC) to enable enhanced remote
support to improve availability. The TSMC can remotely monitor each
attached device to determine if it is working properly and report any
error alerts for the early detection of problems. Use of the TSMC may
expedite microcode updates, reduce service times, and enhance local
service. One of these features must be ordered on any new 3494 Tape
Library Model L12, or L22 instead of the Remote Support features (#2710,
#2711, or #2712). They are recommended on every installed 3494 Tape
Library. Any 3494 VTS, 3590 Model A60, or 3592 Model J70 in a 3494
library should also attach to the IBM TotalStorage Master Console. The
same master console for service may be shared between the following
units:
- 3494 Model AX0, B10, B18, B20, HA1, L10, L12, L14, or L22
- VTC in a 3494 Model CX1
- 3590 Model A60
- 3592 Model J70
To connect a unit to an IBM TotalStorage Master Console, one of the
following three features must be selected on the unit based on the number
of units attached to that master console facility in the installation.
(#2713) Master Console For Service
This feature provides the IBM TotalStorage Master Console, an Ethernet
hub and a cable and connectors for connection of one of the above units
to an IBM supplied modem to enable remote enhanced service. This feature
should be specified on the first unit in an installation connected to a
master console facility. The Ethernet hub provides 14 additional
connections for cables supplied with feature #2714 or #2715.
- Minimum: One of feature #2713, #2714, or #2715 is required on all
new orders of a 3494 Model L12 or L22.
- Maximum: One of #2713, #2714, or #2715. A maximum of one of feature
#2714 may be connected to the Master Console For Service feature #2713.
- Plant or field installable.
(#2714) Console Expansion
This feature provides an attachment cable for connection of one of the
above units, and an Ethernet hub for expanding the number of units that
can be attached to the Master Console For Service (#2713). Up to 14
additional connections are provided by this feature for connection of
#2715 or another #2714.
- Minimum: One of feature #2713, #2714, or #2715 is required on all
new orders of a 3494 Model L12 or L22.
- Maximum: One of #2713, #2714, or #2715. A maximum of one other
Console Expansion (#2714) may be connected to the Ethernet hub provided
by this feature #2714. A maximum of two of feature #2714 may be included
in a single master console facility (providing a total maximum of 43 unit
connections).
- Plant or field installable.
(#2715) Console Attachment
This feature provides a cable to attach a unit to the Ethernet hub
provided by the Master Console For Service (#2713) or the Console
Expansion (#2714). A maximum of 40 of feature #2715 may be included in a
single master console facility.
- Minimum: One of feature #2713, #2714, or #2715 is required on all
new orders of a 3494 Model L12 or L22.
- Maximum: One of #2713, #2714, or #2715.
- Plant or field installable.
Additional Special Features
(#5045) Enhanced Library Manager
(No Longer Available as of February 28, 2003)
This feature provides an enhanced library manager with a mirrored dual
disk, for performance and availability improvements in the 3494. If this
feature is added to a 3494 that includes Model HA1 Frames, feature #5045
must be ordered for both the Model HA1 and the Model L10, L12, or L14.
This feature code is for currently-installed units only.
Maximum: One.
Field Installation Only.
(#5046) PCI Library Manager - Field
(No Longer Available as of October 29, 2004)
This feature provides the field installation of a library manager with
PCI architecture including a faster 1.2 Ghz processor and a mirrored dual
disk drive, for performance and availability improvements in the 3494.
If this feature is added to a 3494 that includes Model HA1 Frames,
feature #5046 must be ordered for both the Model HA1 Frames and the Model
L10, L12, or L14. This feature code is for currently-installed units
only.
- Maximum: One.
- Corequisite: Feature (#5046 or #9046) is required when adding
feature #9040 (High Availability Attachment) to any installed Model L1x
that does not already have feature #9020 (Model B20, B10, or B18
Attachment).
- Field Installation Only.
(#5047) LAN PCI Library Manager - Field Install
This feature provides the field installation of a library manager (LM)
that supports EASH attachment of tape drives attached to open systems and
up to 64 LAN attached open system TCP/IP hosts. The LM has a PCI
architecture and includes a 1.2 Ghz processor and a mirrored dual disk
drive, to help improve performance and availability in the 3494. If this
feature is added to a 3494 that includes Model HA1 Frames, the other LM
must be feature #5046, #9046, or #9047. This feature code is for
installed units only.
Note: This LM does not come with four RS232 host connections and four
tape control unit serial connections. If that capability is required,
the Base Tape Control Unit Attachment feature (#5225) must be ordered
with this feature. Feature #5225 is also required if the other LM in the
3494 Tape Library that includes Model HA1 Frames is not feature #5047 or
#9047.
- Maximum: One.
- Required: Feature #5047 (or #9047) is required when adding feature
#9040 (High Availability Attachment) to any installed Model Lxx that has
a LM shipped prior to May 15, 2000, and the Model Lxx does not contain
feature #5046 or #9046 (PCI Library Manager) or feature #9020 (Model B20,
B18, or B10 VTS Attachment).
- Corequisite: Feature #5225, if RS232 host connection or base tape
control unit serial connection to the LM is required (such as when
replacing an older LM with that connection requirement).
- Field Installation Only.
(#5215) Dual Gripper
Provides accessor performance enhancement in the 3494, for longer
configurations (3 or more units). Installation of dual gripper reduces
the quantity of available storage cells by 10%, this is due to the top
and bottom row of storage cells becoming unavailable. It is required on
the Model HA1 Frames when the Dual Gripper (#5215) is installed on the
Tape Library Base Frame Model L10, L12, or L14.
Maximum: One.
Field Installation: Yes.
(#5219) Token Ring Adapter (#5219)
(No Longer Available as of July 2, 2004)
Allows the 3494 Manager to attach to a token ring LAN. It is required
on the Model HA1 Frames when the Token Ring Adapter (#5219) is installed
on the library manager of the Tape Library Base Frame Model L10, L12, or
L14.
Maximum: One.
Field Installation: Yes.
(#5220) Ethernet Adapter
Allows the 3494 library manager to attach to an Ethernet LAN at up to
100 MB per second. TCP/IP and APPC protocols are supported. The iSeries
supports TCP/IP LAN connections with OS/400 V5R2, and later (AAPC is the
required LAN protocol prior to V5R2). The maximum processor LAN
connections is 32.
- Maximum: One.
- Field Installation: Yes.
(#5222) Additional 32 LAN Host Attachments
This feature provides an update to the microcode firmware of an
installed PCI Library Manager feature (#5046 or #9046) to support up to
64 LAN attached open system hosts. This is double the 32 LAN attached
open system hosts previously available. This capability is included in
the LAN PCI Library Manager feature (#5047 or #9047). The LAN interface
can be through either the Ethernet LAN Adapter feature (#5220) or the
Token Ring Adapter feature (#5219). Support is provided for up to 32
APPC hosts or 64 TCP/IP hosts, or combinations of those attachments.
- Maximum: One.
- Prerequisite: Feature #5046 or #9046.
- Field Installation Only.
(#5225) Base Tape Control Unit Attachment
This feature includes an attachment card that provides four RS232 open
system host connections and four tape control unit serial attachments to
the 3494 library manager (LM). This feature is not required if all open
system attached tape drives are connected to the LM with an EASH
attachment, or if LAN attachment to open system hosts is used instead of
an RS232 attachment. If this feature is added to a 3494 that includes
Model HA1 Frames, the other LM must also have this capability.
- Maximum: One.
- Required:
- If feature #5047 or #9047 is installed and any feature #53xx or #55xx
frame is installed on the 3494 Model Lxx.
- If the 3494 includes Model HA1 Frames and the other LM has feature
#5225, or does not have feature #5047 or #9047.
- Prerequisite: Feature #5047 or #9047.
- Plant or Field Installation.
(#5227) 32 Port Attachment
This feature provides 16 additional RS-422 tape control unit
connections for the Library Manager on a 3494 Enterprise Tape Library.
Use of this feature along with the Expansion Attachment Card (#5229)
provides for a total of 24 RS-422 control unit connections and eight
RS-232 host processor connections. When feature #5227 is installed with
one or two Tape Control Unit Expansion features (#5228), the number of
available tape control unit connections is increased by 16 over the
numbers shown in the table with feature #5228. This allows up to 32 SCSI
or Fibre Channel attached tape drives to be installed in the library.
This feature is required on the Model HA1 when this feature is installed
on the library manager of the Tape Library Base Frame Model L10, L12, or
L14 of that Enterprise Tape Library.
Maximum: One.
Plant or Field Installable.
Prerequisite: Feature
#5229.
Note: If the Model L10, L12, or L14 was installed prior to September,
1997, you must have one of the following features installed:
- Feature #9020 (Model B20, B10, or B18 VTS Attachment)
- Feature #9040 (High Availability Direct Attachment)
- Feature #5045 (Enhanced Library Manager)
(#5229) Expansion Attachment Card
This feature provides an additional attachment card in the library
manager of the Model HA1 Frames. It is required on the Model HA1 when
the Expansion Attachment Card (#5229) is installed on the library manager
of the Tape Library Base Frame Model L10, L12, or L14.
Maximum: One.
Field Installation: Yes.
None.
Back to top
Accessories
|
None.
Customer Replacement Parts
None.
Back to top
Machine Elements
|
None.
Back to top
Supplies
|
None.
Diskettes
None.
Trademarks
(R), (TM), * Trademark or registered trademark of International
Business Machines Corporation.
** Company, product, or service name may be a trademark or service
mark of others.
© IBM Corporation 2004.
Back to top
|
|
|
|